Showing posts with label uphosltery. Show all posts
Showing posts with label uphosltery. Show all posts

May 2, 2010

window seat taa-daa!

Confession:  I lost the 'before' picture for this project.

I swear I took the pic.  But where is it?
I've search through the endless piles of photo chaos on my computer.  Oh, don't judge me.  You know the photo chaos...you've been lost in it too. 
The abyss of unmarked photos scattered all over your computer.  

Promise: I promise to save my pictures in a marked and uber-organized way.  At lease until I'm in a hurry or the cheese quesadillas are burning...

Craigslist rules!  I found a photo similar to the coffee table I originally bought.
My coffee table cost me $10 bucks.  But, I needed a window seat!  
I was looking something with modern lines and a neutral feel.

TAA-DAA!!




This was an easy project with some basic upholstery. 

Step #1: Prep and paint the wood frame.
After removing the lovely smoke mirrored glass, I painted the table and then sanded up the edges a bit to let the dark wood show through.

Step #2: Cut some wood board to replace the glass mirrors. 

Step #3: Cut a piece of foam for the bench seat.  The best way to cut foam is a band saw.  But if you don't have one, the second best way is with a sereded kitchen knife.
Glue the foam to the board using spray adhesive.


Step #4: Using a staple gun, cover the foam with a liner cloth. 
Securely staple on the backside of the board.  Use a firm even pressure around the edges.  As you can see in the picture, I use my body weight to push foam in and then staple the fabric.  This makes a nice rounded edge on your seat. 


Step #5: Cover your seat with the upholstery fabric.
Using the same technique as the liner cloth, use a firm even pressure and staple the fabric in place.  Always cut away and excess fabric.  Pull your corners in and staple them like crazy. Remember, the underside of your project doesn't have to look perfect.  This is not an art of perfection...and that's why I love it!  Also, I'm using an air powered staple gun, which is the bomb.  If you don't have access to one of these, a hand powered gun is great.  I've done many many project with a hand gun.
Step #6: Staple your trim.
Adding a trim gives finished look to your project.  Here I choose a burlap natural fiber that fit in with my neutral scheme.  Simply, staple the trim along the edge of your board. 
 
Here's a trick I learned from a great upholsterer, when the two ends of your trim meet, simply unravel the ends, cross them over each other and staple in place on the underside of the board. This way your cushion will fit perfectly without the added bulk of the extra trim.


 Step #7: Put your bench together.
Add a few L brackets to secure your seat.

That's it!
Enjoy your bench!




April 12, 2010

Meet Brittany

Peppertowne Reader Before & After:
Meet Brittany

I love button tuffting and usually I love orange,
but this retro 70's style rocker had to go.  
In Brittany's words..."YUCK!"
She tackled a tough project that took her more than 6 months and cost her a few bodily injuries!!
Amazing how this red micro-fiber brings this rocker into 2010.

Now just add a pillow
 and her two adorable children reading bed time stories.
Picture perfect.
This upholstery job looks so professional.
Thanks for sharing Brittany!

If you have a before and after project you'd like to feature on Peppertowne, email your low resolution photos here.

Linking up:
The Persimmon Perch
Sumos Sweet Stuff
The Creative Girl
Making the World Cuter
Cottage Instincts
Skip to my Lou
Between Naps on the Porch
Silly Little Sparrow
The Herber Family
Reinvented

March 8, 2010

DIY: Button Tufted Ottoman

I have fallen in love with tufting! The look and feel are so lux.
This used ottoman was a thrift store find that needed a little love.
Now, it's a perfect place for your feet!
Supplies & Tools
Safety goggles (If I didn't mention these, I'd get in trouble with my father-in-law)
One old, dilapidated ottoman
Flathead screwdriver or other flat pointed tool for removing staples
Needle nose pliers
Buttons
Spray adhesive
Long upholstery needle and knitting needle
Upholstery fabric (I used 2 yards)
Liner fabric (I used 1 1/2 yards)
Finishing fabric and ribbon
(I used 1 yard fabric & 2 1/2 yards ribbon)
Thin sheet of plywood
Staples & staplegun
Upholstery string or twine
Screws or nails
Hammer and drill
Hot glue and glue gun
and...
One eager little helper.

Step One:
Strip your ottoman down.  Remove the legs (they usually screw out) and all the fabric, removing as many staples as you have patience for.  This ottoman had 4 layers of fabric!  Seperate the top foam and batting piece from the bottom hardware.  If the foam and batting are in bad shape, replace it. 


Step Two
Measure your ottoman and cut the plywood to be about 1 inch shorter around the edges.  Measure and pre-drill holes for your buttons.  Buttons are usually attached in a grid or diamond pattern.  For this ottoman I spaced 9 buttons in a grid. I drew my grid and drilled the holes using the
largest drill bit in my Man's workshop.  Using spray ahesive, attach the board to the backside of your foam.

Step Three
Attach your liner.  A liner can be any simple cotton fabric or even an old sheet.  The purpose is to control the shape of your foam and batting.  Start stapling in the center of each side.  Stretch the fabric tightly to create an even shape.  Then work the corners of the ottoman in the same way folding the excess in.  Next, finish the edges stretching the fabric firmly.  If you have any gaps, like in photo #3, just pull tight and staple.
Don't be afraid to get staple-happy!  You can never use too many.

Once the liner is attached, assemble your ottoman upside down and centered on your upholstery fabric.  Use your eye to measure how much fabric you will need to cover each side.  Then remove the bottom harware piece so you can begin adding the buttons to your foam.
This is the fun part!


Step Four
Using upholstrey twine thread your button.  To do this, first, fold your twine in half creating a loop.  Thread the loop through the button and double it over so that the button is attached to the twine. 
Use the knitting needle to push through your pre-drilled hole into the foam and out the front side of your fabric.  Poke the needle in and out and few times to create a path for your upholstrey needle.
Starting from the foam side, or back side, push your upholstrey needle through the hole and out the top of the fabric.  Then slip the two loose ends of the twine into the eye of the needle and pull the needle out the bottom.  You may need to use your needle nose pliers.  Remove the needle and pull the twine and button tight.  Attach the twine with staples in a zig-zag pattern and then tie a knot.  This holds the button firm.  Make sure each button is pulled with the same tightness to ensure an even uniform look.



Step 5
Assemble your ottoman.  I attached the bottom and top piece with a few screws.  I drilled my holes and then inserted the screws to hold the pieces securely together.  I prefer screws over nails because the wood on this ottoman is brittle and could split. 
 

Step Six
There will be a natural pucker of fabric at each button.  Starting at the center, fold the pucker and pull it tightly toward the bottom of the ottoman.  It's important to pull tightly on the fabric.  Loose upholstrey will look awful.  Secure the fabric firmly with your staple gun.  Use a hammer to tighten any loose staples.
Next fold your corners.  Pull the excess fabric out (like picture #4) and then fold the seams in and staple
(picture #5).

Cut away excess fabric from the center and make sure all edges are tightly stapled.

Step Seven
Attach your finishing fabric.  Use any cotton fabric to finish the bottom of your awesome new tufted ottoman.  Pull the fabric tightly across and staple.  Again, nailing down any loose staples.  Next, hot glue a ribbon around the bottom fabric seam to hide the unfinished edges.  Then, screw the feet back into place. 


Ooooh La La! A beautiful velvet tufted ottoman!
Now kick your feet up and relax.


You can do it!

If you'd like to share a great before and after project on our blog, simply email your low-resolution before and after pictures here and we'll feature you.

Related Posts Plugin for WordPress, Blogger...